EarthQuake CS4518B Instrukcja Operatora

OperatOr's Manual & partsChain Saw CS4518 GetEarthquake.comOMCS4518R072409© Copyright 2009 Ardisam, Inc.All Rights Reserved. Printed in China

Page 10 12. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and the muffler away from your

Page 11 19. Guard against kickback. Kickback is the upward motion of the guide bar which occurs when the saw chain at the nose of the g

Page 12 (2) Keep a good grip on the saw with both hands, the right hand on the rear handle, and the left hand on the front handle, when

Page 13 A standard saw unit package contains the items as shown below.： (1) Power unit (2) Guide bar (3) Saw chain

Page 14 NOTE Pay attention to the correct direction of the saw chain. 1：Moving direction 4. Mount the guide bar th

Page 15 Fuel The engines are lubricated by Viper Engine Oil specially formulated for air-cooled 2-cycle gasoline engine use. If o

Page 16 4. Pour in the rest of gasoline and agitate again for at least one minute. 5. Put a clear indication on the outside of t

Page 17 STARTING ENGINE 1. Untwist and remove the fuel cap. Rest the cap on a dustless place.. 2. Put fuel into the fuel tank to

Page 18 8. When firing occurs, push in the choke knob and pull the starter again to start the engine. 9. Allow the engine to warm

Page 19 When adjusting, take the following steps: IMPORTANT Be sure to adjust the carburetor with the bar chain attached. 1

Page 20 To release brake, pull up the front handle guard toward the front handle till “click” sound is heard. WARNING When

Page 21 WARNING Before proceeding to your job, read "For Safe Operation" section It is recommended to first practice saw

Page 22 Felling a Tree 1. Decide the felling direction considering the wind, Iean of the tree, location of heavy branches, ease

Page 23 LOGGING AND LIMBING WARNING 1. Always ensure your foothold as well as stability of the tree. 2. Be alert to the ro

Page 24 Pruning Cut up from the bottom, finish down from the top. WARNING 1. Do not use an unstable foothold or a stepladde

Page 25 WARNING Before cleaning, inspecting or repairing your unit, make sure that engine has stopped and is cool. Discon

Page 26 (2) Grease port (3) Sprocket 4. Others Check fo

Page 27 3. Oil tank With a wire hook, take out the oil filter through the filler port and clean in gasoline. When putting the filte

Page 28 Saw chain WARNING It is very important for smooth and safe operation to keep the cutters always sharp. Yo

Page 29Maintenance of Chain / BarAfter every cutter has been set, check the depth gauge and file it to the proper level as illustrated. WARNINGBe sure

Page 3SAFETY FIRSTInstructions contained in warnings within this manual marked with a WARNINGsymbol concern critical points which must be taken into c

Page 30WARNINGThis saw is equipped with the following low kickback bar/chain combination:Guide bar:Oregon180SDEA095Saw chain:3/8 low profile reduced ki

Page 311. Empty the fuel tank and run the engine out of fuel.2. Empty the oil tank.3. Clean the entire unit.4. Store the unit in a dry place out of th

Page 34Troubleshooting GuideProblem Cause RemedyStarting failure Check fuel for water or substandard mixtureReplace with proper fuelRemove and dry the

Page 35SpecificationsPower unit：Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45.02ccMax

Page 361-Year Limited WarrantyTerms and ConditionsArdisam, Inc., a manufacturing company, warrants this Earthquake® CHAIN SAW to be free from defects

Page 40Earthquake, Division of Ardisam, Inc. • 1160 Eighth Avenue; P.O. Box 666Cumberland, Wisconsin 54829800-345-6007 · Fax (715) 822-4180 • E-mail:

Page 41. Front hand guard and brake2. Starter handle3. Air filter cover4. Choke knob5. Throttle trigger lock-out6. Rear handle7. Throttle trigge

Page 5 (1) Read operator's instruction book before operating this machine. (2) Appropriate ear, eye, and head protection must be wo

Page 6For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a

Page 7 (f). The screw under the "H" stamp is The High-speed adjustment screw. The screw under the "L" stamp is The

Page 8Before operating the product 1. Before using our products, please read this manual carefully to understand the proper use of your

Page 9 6. Always use caution when handling fuel. Wipe up all spills and then move the chain saw at least ten(10)feet (three(3)